Up one chapter


view larger image

Begin OCR Text:
2. __açe _he ba__ jojnt in pogition on the Steering knuCkle and fit the clamping bolt. 3. _onneç_ the upper wishbone to the ball joint _ and fit the attach_ng bolts. q. fit the whee_ and sCrew on the wheel nUtS. _ _ower the vehiçle and final-tighten the Wheel nuts. 3 2 _OWE_ _A__ JOlNT _ _E_OVIN_ 1. __açken the wheel nutS SeVeral tUrns. _ d __C.II__J 2. ffaige the front end and p_aCe a treSt g Un er '''__' the _ower wighbone. UnsCrew the Wheel nutS and take down the whee_. Flg. 6_26. LDwer ball ioint att8_hment u h (6 F 6 26) d th _ Lower b8ll _oint 7. Br8cket 3 ngçreW t e nUtS Ig - an remOVe e _ d g g _ ' ' ' 2 PIn _e Ot four bo_tS (8). ffemove the nut (3). 3 Castle nut 9. Circlip h F h 4 _plit p_n 1O. Rubber couer 4. DisConneCt the brake OSeS rO__ t e feta_ner_ _. _owe_ w_ghbone 11 Circ1ip _it too_ _\/_ ___1 _o the gteerin_ knuçk_e, gee 6 NUt 'Fig. 6-'25U. 'PUrokbkaUbly' the retainerYfor the brake lines may have to be bent Slightly to the one side. Turn the tool nut until the tool starts to F___N_ t _ __ t t_ _ t__ t_ _ __ _ _ t enSlOn. Inen Urn ne nU_ Un Il ne Dall )Oln re_eageS but maK _ 1/2 turng _F the ba__ )_o__nt 1. _heçk to make gure the rubber Seal iS not da- ._g go SeC'ure_y F_tte'd that ._t çann' ot be g_açkened maged and fil_ with grease. _f neCeSSary, flll w__t_ t___g turn__ng try tapping ___g_t tapg w_jt_ a with univerga_ gre3se. _ake gure that the SleeUe ham_me_r and C'ounterho_d o'n _the gteer___ng and _oçk ringg take up the_r proper poSition. See _nuC__e_g _a_j)o__nt attaC_ment. flg. 6-26. _ _' U ' _ 2. fit the ba__ joint in pogition on the Steering , knuçk_e and fit the nut. Tighten the nUt to a torqUe of 4.8-5.5 kpm (35_O _b.ft.). 3. _onneCt the lower ba__ jointto the WiShbOne and fit the four attaching bolts. 4. f_t the brake hoses and b_eed the brake Caliper. 5. Fit the whee_ and wheeI nuts. LoWef the uehiCle and final-tighten the wheel nUtS. fit the hUb Cap. U__E_ Wl_H_ONE _E_LA__N_ _U_HE_ t. _lacken the wheel nutS Several tUrnS. 2. ffaige the front end and plaCe a treStle under the lower wishbone. Unscrew the wheel nuts and lift off the wheel. 3. Unscrew the nuts (6, Fjg. 6-13) and remove the C_ampS (4). 4. _end up the Ioçk plate (3, fig. 6-7). unsCfew the attaching bolts (2) and remove the shaft. o Take care of the shims (1). V'''_''_'_ 5. Remove the nuts (Fig. 6-13). the washers (2). the Fig. 6-Z_. Removing lower ball joint buSheS (3) and the SleeVeS (5). 6. 14
 
Not associated with Volvo AB Sweden or Volvo Cars of North America